Mechanical In-Cab Controls

Operate your air springs (or other pneumatic accessories) right from the driver’s seat with
mechanical AMP In-Cab Controls.

Various dash activation switch kits are available depending on your air spring operation requirements:

‘Simultaneous’ inflation uses a single switch that inflates/deflates both air springs at the same time.

‘Independent’ inflation is achieved with 2 separate switches, allowing the inflation/deflation of each air spring individually to customize your front-to-back & side-to-side adjustability.

 
PREMIUM PADDLE VALVE IN-CAB CONTROL KITS

Premium In-Cab Control Kits come with everything you need to operate your air springs (or other pneumatic accessories) right from the driver’s seat including an HP325 compressor, nylon hose, wire, fittings, fasteners, electrical terminals and in-line fuse holders.

‘Simultaneous’ kits inflates/deflates both air springs at the same time while ‘Independent’ kits allow for inflation/deflation of each air spring individually.

SIMULTANEOUS AIR SPRING DASH SWITCH

HP10135

HP325 Air Compressor Specifications:

  • 12 VDC
  • 33% duty cycle (20 Minutes @ 100 psi), 1.2 CFM
  • 150 psi max operating pressure, draws 18 amps

Air Tank Options:

*Please Note: If adding an air tank, a pressure switch is required.
HP10110 is for 105-135 PSI and HP10111 is for 85-105 PSI

INDEPENDENT AIR SPRING DASH SWITCHES

HP10098

HP325 Air Compressor Specifications:

  • 12 VDC
  • 33% duty cycle (20 Minutes @ 100 psi), 1.2 CFM
  • 150 psi max operating pressure, draws 18 amps

Air Tank Options:

*Please Note: If adding an air tank, a pressure switch is required.
HP10110 is for 105-135 PSI and HP10111 is for 85-105 PSI

 
BASIC PADDLE VALVE IN-CAB CONTROLS – For use with existing onboard air

An economical option for operating air spring kits with a pneumatic dash switch(es) that attach directly to the existing tank and the air springs. Choose between simultaneous or independent air spring inflation/deflation.

Air tank and solenoid blocks are not required for this method of in-cab air control operation, however, should you decide to add an air tank for stored onboard air, you can do so by adding either our HP10053 ½ gallon or HP10050 2½ gallon air tank kit*.

SIMULTANEOUS ACTIVATION

HP10133
    This simultaneous dash activation kit is designed to integrate in-cab air spring control with a pre-existing air system.
     
    Use this kit in conjunction with one of our air tank kits and air compressor kits to build your own customizable onboard air system:

Air Tank Options:

*Please Note: If adding an air tank, a pressure switch is required.
HP10110 is for 105-135 PSI and HP10111 is for 85-105 PSI

INDEPENDENT ACTIVATION

HP10124
    This independent dash activation kit is designed to integrate in-cab air spring control with a pre-existing air system.
     
    Use this kit in conjunction with one of our air tank kits and air compressor kits to build your own customizable onboard air system:

Air Tank Options:

*Please Note: If adding an air tank, a pressure switch is required.
HP10110 is for 105-135 PSI and HP10111 is for 85-105 PSI

 
BASIC ELECTRICAL IN-CAB CONTROL KITS – For use with existing onboard air

These kits allow operation of your air springs either simultaneously or independently from the comfort of your driver’s seat. Featuring back-lit dual needle gauge, an ON/OFF activation switch to control compressor operation, and switch(es) for inflation/deflation of the air springs.

Pacbrake’s unique two way solenoid block gives you the option to stack and combine additional blocks to run your vehicle’s air accessories from one central block.

In addition to the solenoid block, each kit comes complete with a nylon hose, wire, fittings, fasteners, electrical terminals and in-line fuse holders.

SIMULTANEOUS ACTIVATION

HP10022

Specific Kit Info:

  • Air spring inflation kit
  • 12 VDC electric actuated two-way pneumatic solenoids
  • Solenoids are stackable for multi-application use
  • Use this kit in conjunction with one of our air tank kits and air compressor kits to
    build your own customizable onboard air system

INDEPENDENT ACTIVATION

HP10062

Specific Kit Info:

  • Air spring inflation kit
  • 12 VDC electric actuated two-way pneumatic solenoids
  • Solenoids are stackable for multi-application use
  • Use this kit in conjunction with one of our air tank kits and air compressor kits to
    build your own customizable onboard air system

 

Find a dealer in your area, or call us at 800.663.0096
FIND A DEALER