Showing 1 to 14 of 14 Products
- Universal
- Snap-in mounting
- Fit .520" X .776" [13.2 mm X 19.7 mm] openings
- .187" [4.75 mm] wide blade terminals
- Plastic body
- Universal
- Snap-in mounting
- Fit .520" X .776" [13.2 mm X 19.7 mm] openings
- .187" [4.75 mm] wide blade terminals
- Plastic body
- Universal
- 27.5° throw
- Black thermoplastic construction - meets FMVSS 302 flammability requirements
- Supply and delivery ports: barbed fitting - accepts 3/16" ID tube - vented to atmosphere through rear of switch
- Fits .89" X 1.61" [22.6 mm X 40.9 mm] openings, R.063" [R1.6 mm] max corner radii, .084" to .125" [2.13 mm to 3.18 mm] panel thickness
- Rated for steady state direct current (DC) of 7.5 A maximum
- Maximum voltage of 15 VDC at zero current
- Maximum 25% duty cycle - maximum "on" time 60 seconds
- Voltage drop across lead wire terminal will not exceed 0.52 VDC at 7 A direct current
- 24" [609 mm] wire leads
- Dual Input (Dual Needle)
- Replacement Part
- Mounting hardware included
- Universal
- 1/8" - 27 NPT — 4 Ports
- Voltage Range: 12 VDC
- Coil Resistance: 25 Ω
- Energize Time: 0.012 ms
- De-energize Time: 0.006 sec
- Universal
- Spring return, normally retracted
- Clear Anodized, front & rear end caps
- Clevis mount
- Operating pressure 100-150 psi
- Buna HBNR seal
- Replacement Part (Non-repairable)
- Universal
- Fits all Pacbrake HP90 and HP325 air compressors
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Universal
- Replacment part
- Corrosion proof stainless steel exterior
- Zero reverse leakage
- Compatible with all HP325 Compressors
- Compatible with all HP325 Compressors
- Universal
- Schrader valve on both ends.
- 16 feet of Nylon 1/4 inch air tubing
- Wall thickness 0.040 inches
- For HP325 compressors
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Universal
- Snap-in mounting
- Fit .520" X .776" [13.2 mm X 19.7 mm] openings
- .187" [4.75 mm] wide blade terminals
- Plastic body
- Universal
- Snap-in mounting
- Fit .520" X .776" [13.2 mm X 19.7 mm] openings
- .187" [4.75 mm] wide blade terminals
- Plastic body
- Universal
- 27.5° throw
- Black thermoplastic construction - meets FMVSS 302 flammability requirements
- Supply and delivery ports: barbed fitting - accepts 3/16" ID tube - vented to atmosphere through rear of switch
- Fits .89" X 1.61" [22.6 mm X 40.9 mm] openings, R.063" [R1.6 mm] max corner radii, .084" to .125" [2.13 mm to 3.18 mm] panel thickness
- Rated for steady state direct current (DC) of 7.5 A maximum
- Maximum voltage of 15 VDC at zero current
- Maximum 25% duty cycle - maximum "on" time 60 seconds
- Voltage drop across lead wire terminal will not exceed 0.52 VDC at 7 A direct current
- 24" [609 mm] wire leads
- Universal
- Air Pressure Sensor
- Dual Input (Dual Needle)
- Replacement Part
- Mounting hardware included
- Universal
- 1/8" - 27 NPT — 4 Ports
- Voltage Range: 12 VDC
- Coil Resistance: 25 Ω
- Energize Time: 0.012 ms
- De-energize Time: 0.006 sec
- Universal
- Spring return, normally retracted
- Clear Anodized, front & rear end caps
- Clevis mount
- Operating pressure 100-150 psi
- Buna HBNR seal
- Replacement Part (Non-repairable)
- Universal
- Fits all Pacbrake HP90 and HP325 air compressors
- Universal
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Universal
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Universal
- Replacment part
- Corrosion proof stainless steel exterior
- Zero reverse leakage
- Universal
- Schrader valve on both ends.
- 16 feet of Nylon 1/4 inch air tubing
- Wall thickness 0.040 inches
- For HP325 compressors
- Universal
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
- Required when adding an Air Tank to any of Pacbrake's Paddle Valve In-Cab Control Kits.
- Rated for 105-135 psi
Showing 1 to 14 of 14 Products